KREVO Inject PU-Flex
Two-component flexible polyurethane injection resin · Elastic sealing of concrete cracks and leaking joints
- Type
- PU Injection Permanent
- Pack sizes
- Standard Flex pack: 10 L set: Part A 5 L; Part B 5 L; High Flex packs: 15 L set: 10 L A + 5 L B; or 7.5 L: 5 L A + 2.5 L B
- Shelf life
- 12 months; unopened containers in dry conditions at about +25 °C
See it applied
Injecting basement cracks
How KREVO Inject PU-Flex goes on site, step by step.
- 1 Stop active leaks
- 2 Inject the cracks
Illustration of the application process, not footage of a specific project. Follow the technical data sheet for the full method.
Overview
KREVO Inject PU-Flex is a low-viscosity, solvent- and phthalate-free, two-component flexible polyurethane injection system for sealing cracks in concrete and masonry. Mixed resin cures to an elastic, adherent material that tolerates limited differential movement. Two performance configurations are described: Standard Flex and High Flex.
Advantages
- Low viscosity promotes penetration into fine cracks and injection ports.
- Flexible cured resin accommodates limited differential substrate movement.
- Bonds to sound dry or damp concrete and masonry surfaces.
- Can be used as a final seal after preliminary control of active water flow.
- Intended for specialist injection with electric or pneumatic pumps.
Typical uses
- Crack sealing in concrete and masonry
- Beams, slabs and columns
- Basements and retaining walls
- Liquid-retaining structures
- Leaking construction joints
- Sewage treatment facilities
Technical data
Technical properties
Typical values from the technical data sheet. Always confirm with the current data sheet before use.
Specification
- Generic type
- Two-part low-viscosity flexible polyurethane injection resin
- Binder / chemistry
- Solvent- and phthalate-free polyurethane base (A) + hardener (B)
- Performance configurations
- Standard Flex and High Flex (technical alternatives)
- Mix ratio by volume
- Standard Flex 1:1 | High Flex 2:1 (A:B)
- Use / finish
- Elastic sealing of non-structural cracks and construction joints
- Shelf life / storage
- 12 months; unopened containers in dry conditions at about +25 °C
- Standard Flex tensile strength | 7 d
- 3.5 ± 0.5 MPa (ASTM D638)
- High Flex tensile strength | 7 d
- 4.0 ± 0.5 MPa (ASTM D638)
- Standard Flex elongation at break | 7 d
- 90 ± 20% (ASTM D638)
- High Flex elongation at break | 7 d
- 170 ± 20% (ASTM D638)
- Standard Flex mixed viscosity
- 240–280 mPa·s (at +25 °C / 50% RH)
- High Flex mixed viscosity
- 50–90 mPa·s (at +25 °C / 50% RH)
- Pot life | both configurations
- 60–80 minutes (at +25 °C / 50% RH)
- Reference minimum crack width
- 0.1 mm (ductile filling technical criterion)
- VOC | reference information
- ≤150 g/L; manufacturer verification required
Used together with
Leak sealing and crack injection
KREVO Inject PU-Flex is one step of this system, as shown in our application film. Follow each product's data sheet for compatibility and overcoating times.
-
1Stop active leaks
-
2Inject the cracks
KREVO Inject PU-Flex
This product
FAQ
KREVO Inject PU-Flex: questions
What is KREVO Inject PU-Flex?
KREVO Inject PU-Flex is a low-viscosity, solvent- and phthalate-free, two-component flexible polyurethane injection system for sealing cracks in concrete and masonry. Mixed resin cures to an elastic, adherent material that tolerates limited differential movement. Two performance configurations are described: Standard Flex and High Flex.
What is KREVO Inject PU-Flex used for?
KREVO Inject PU-Flex is used for: crack sealing in concrete and masonry; beams, slabs and columns; basements and retaining walls; liquid-retaining structures; leaking construction joints; sewage treatment facilities.
How is KREVO Inject PU-Flex applied?
In outline: 1. Stop active leaks 2. Inject the cracks. The video on this page shows the process; always follow the technical data sheet for surface preparation, mixing and application details.
What pack sizes is KREVO Inject PU-Flex available in?
KREVO Inject PU-Flex is supplied in Standard Flex pack: 10 L set: Part A 5 L; Part B 5 L; High Flex packs: 15 L set: 10 L A + 5 L B; or 7.5 L: 5 L A + 2.5 L B.
What is the shelf life of KREVO Inject PU-Flex?
Shelf life / storage: 12 months; unopened containers in dry conditions at about +25 °C.
Is there a technical data sheet for KREVO Inject PU-Flex?
Yes. The technical data sheet (PDF) can be downloaded from this page. For project-specific advice or a quotation, send an enquiry to the Krevo technical team.
More in Injection System
Water Plug
Injection System
KREVO Plug Rapid
Ultra-rapid-setting water-stopping mortar · Single-component · Active leak plugging
View product
PU Injection Temporary
Injection System
KREVO Inject PU-Foam
Water-reactive two-component polyurethane injection foam · Rapid stopping of active leaks
View product
Cementitious Injection
Injection System
KREVO Inject MicroCem
High performance ultra-fine injection cement · Concrete and geotechnical grouting
View product