Skip to content
Krevo
KREVO Repair MicroConcrete
Concrete Repair

KREVO Repair MicroConcrete

Free-flowing high-strength cementitious micro-concrete · Non-shrink repair and grouting · 50-500 mm

Type
Micro Concrete
Pack sizes
40 kg bags
Shelf life
6 months minimum from manufacture in original unopened bags
Technical data sheet

Overview

KREVO Repair MicroConcrete is a single-component, free-flowing, shrinkage-compensated cementitious micro-concrete formulated with Portland cement, selected aggregates and special additives. With a maximum aggregate size of 10 mm, it is designed for formed repair of deteriorated structural concrete and controlled grouting in hot or tropical conditions.

Advantages

  • Single-component dry material requiring only measured clean water.
  • Free-flowing consistency for congested and formed repair sections.
  • Shrinkage-compensated with rapid strength development.
  • Strong adhesion and compatibility with conventional structural concrete.
  • Convenient installation, reduced mixing waste and vapour permeability.

Typical uses

  • Structural repair of beams, columns and concrete members
  • Formed reinstatement of damaged sections
  • Voids and inaccessible repair zones
  • Small-volume cast-in-place repairs
  • Thick-section baseplate grouting above 100 mm

Technical data

Technical properties

Typical values from the technical data sheet. Always confirm with the current data sheet before use.

Full data sheet

Key performance

KREVO Repair MicroConcrete

10 mm

Maximum aggregate size

≥ 35 MPa

Compressive strength | 1 day

≥ 40 MPa

Compressive strength | 3 days

≥ 45 MPa

Compressive strength | 7 days

≥ 65 MPa

Compressive strength | 28 days

2.3%

Water absorption | BS 1881, 28 days

2.5 kg/L

Fresh mortar density

30 minutes

Pot life | +25 °C

Product information

Material type
Single-component, free-flowing, shrinkage-compensated cementitious micro-concrete
Chemical base
Portland cement, selected graded aggregates and special additives
Appearance
Grey powder
Shelf life
6 months minimum from manufacture in original unopened bags
Storage
Cool, dry conditions at +5 °C to +35 °C; protect from heat, sunlight and moisture
Water-to-powder ratio
0.08-0.11 (approximately 3.2-4.0 L water per 40 kg bag)
Compressive-strength test basis
ASTM C109 / C1107 as stated in supplied specification
Yield per 40 kg bag
18.4 liter

FAQ

KREVO Repair MicroConcrete: questions

What is KREVO Repair MicroConcrete?

KREVO Repair MicroConcrete is a single-component, free-flowing, shrinkage-compensated cementitious micro-concrete formulated with Portland cement, selected aggregates and special additives. With a maximum aggregate size of 10 mm, it is designed for formed repair of deteriorated structural concrete and controlled grouting in hot or tropical conditions.

What is KREVO Repair MicroConcrete used for?

KREVO Repair MicroConcrete is used for: structural repair of beams, columns and concrete members; formed reinstatement of damaged sections; voids and inaccessible repair zones; small-volume cast-in-place repairs; thick-section baseplate grouting above 100 mm.

What pack sizes is KREVO Repair MicroConcrete available in?

KREVO Repair MicroConcrete is supplied in 40 kg bags.

What is the shelf life of KREVO Repair MicroConcrete?

Shelf life / storage: 6 months minimum from manufacture in original unopened bags.

Is there a technical data sheet for KREVO Repair MicroConcrete?

Yes. The technical data sheet (PDF) can be downloaded from this page. For project-specific advice or a quotation, send an enquiry to the Krevo technical team.

Ask our team

About: KREVO Repair MicroConcrete