Skip to content
Krevo
KREVO Shield EP-ZP
Coatings & Linings

KREVO Shield EP-ZP

High-build epoxy zinc-phosphate primer · Phenalkamine cured · Industrial steel protection

Type
Zinc Phosphate Primer
Pack sizes
19 L kit (approx. 30 kg shipping); at least 12 months unopened
Coverage
9.8 m²/L at 75 µm; 4.2 m²/L at 175 µm, before loss
Technical data sheet

Overview

KREVO Shield EP-ZP is a two-component, high-build phenalkamine epoxy coating containing zinc-phosphate anticorrosive pigment. Designed for protective coating of suitably prepared steel, it can be used as a primer or intermediate coat in industrial atmospheric coating systems. Its surface- tolerant properties and short recoat intervals support maintenance applications.

Advantages

  • High-build epoxy coating with zinc-phosphate anticorrosive pigmentation.
  • Short recoating intervals support efficient protective-coating operations.
  • Suitable as a primer or intermediate coat in compatible coating systems.
  • Good surface tolerance and controlled moisture tolerance during application.
  • Can be used with selected acrylic, alkyd, epoxy or polyurethane topcoats.

Typical uses

  • Structural steel
  • Process plants and pipework
  • Industrial steelwork
  • Marine and coastal atmospheric exposure
  • Maintenance and refurbishment of suitably prepared steel

Technical data

Technical properties

Typical values from the technical data sheet. Always confirm with the current data sheet before use.

Full data sheet

Specification

Generic type
Two-component phenalkamine epoxy with zinc phosphate
Colours
Red or grey
Finish
Satin to low-sheen semi-gloss
Recommended dry film thickness
76–178 µm (3–7 mils) per coat
Volume solids
Approximately 75% ± 2%
Theoretical coverage
9.8 m²/L at 75 µm; 4.2 m²/L at 175 µm, before loss
Mixing ratio (A:B)
6:1 by volume; power mix full kits
VOC as supplied
220 g/L
Pot life at 25 °C
2 hours; shorter at higher temperatures
Dry temperature resistance
93 °C continuous; 121 °C intermittent
Airless spray thinning
Up to 15% with approved compatible thinner
Brush / roller thinning
Up to 5% with approved compatible thinner
Steel blast cleaning
SSPC-SP 6 / ISO 8501-1 Sa 2½; 25–50 µm profile
Galvanized steel preparation
Remove contamination; abrade / sweep blast to adequate key
Topcoats / service
Acrylic, alkyd, epoxy or polyurethane; atmospheric service

FAQ

KREVO Shield EP-ZP: questions

What is KREVO Shield EP-ZP?

KREVO Shield EP-ZP is a two-component, high-build phenalkamine epoxy coating containing zinc-phosphate anticorrosive pigment. Designed for protective coating of suitably prepared steel, it can be used as a primer or intermediate coat in industrial atmospheric coating systems. Its surface- tolerant properties and short recoat intervals support maintenance applications.

What is KREVO Shield EP-ZP used for?

KREVO Shield EP-ZP is used for: structural steel; process plants and pipework; industrial steelwork; marine and coastal atmospheric exposure; maintenance and refurbishment of suitably prepared steel.

What pack sizes is KREVO Shield EP-ZP available in?

KREVO Shield EP-ZP is supplied in 19 L kit (approx. 30 kg shipping); at least 12 months unopened.

What is the coverage of KREVO Shield EP-ZP?

Coverage / consumption: 9.8 m²/L at 75 µm; 4.2 m²/L at 175 µm, before loss. Actual consumption depends on the substrate and application; see the technical data sheet.

Is there a technical data sheet for KREVO Shield EP-ZP?

Yes. The technical data sheet (PDF) can be downloaded from this page. For project-specific advice or a quotation, send an enquiry to the Krevo technical team.

Ask our team

About: KREVO Shield EP-ZP