KREVO Inject MicroCem
High performance ultra-fine injection cement · Concrete and geotechnical grouting
- Type
- Cementitious Injection
- Pack sizes
- 25 kg bags
- Shelf life
- Dry, shaded conditions, below +25°C
Overview
KREVO Inject MicroCem is an ultra-fine blast furnace slag cement system for penetrating fine cracks and voids in concrete, rock and soil. It is intended for specialist injection grouting, ground improvement and upgrading conventional cement grouts and mortars. Two fineness grades, B6 and B10, allow selection to suit the project.
Advantages
- Very fine particle size and high penetrability in suitable cracks and porous media.
- Low permeability and good long-term durability after appropriate curing.
- High resistance to sulfate- and chloride-bearing environments.
- Mineral-based, non-toxic injection-grouting technology.
- Choice of B6 and B10 grades to match penetration and grout-mix requirements.
Typical uses
- Concrete crack injection
- Soil and rock stabilization
- Foundation support
- Sealing of sheet piles
- Groundwater cut-off and underground stream sealing
- Performance enhancement of cement-based grouts and mortars
Technical data
Technical properties
Typical values from the technical data sheet. Always confirm with the current data sheet before use.
Specification
- Generic type
- Ultra-fine blast furnace slag injection cement
- Available grades
- B6 (maximum 6 µm) and B10 (maximum 10 µm)
- Form
- Dry ultra-fine cementitious powder
- Principal applications
- Concrete crack injection; soil, rock and foundation grouting
- Binder performance
- High strength after curing; values vary by grade
- Storage
- Dry, shaded conditions, below +25°C
- Shelf life
- 6 months in unopened, properly stored bags
- Maximum grain size
- B6: 6 µm | B10: 10 µm
- Blaine specific surface
- B6: ~1,900 m²/kg | B10: ~1,600 m²/kg
- Median particle size, d50
- B6: ≤2.5 µm | B10: ≤3.5 µm
- Particle size, d95
- B6: ≤6 µm | B10: ≤9.5 µm
- Compressive strength, 1 day
- B6: ≥25 MPa | B10: ≥10 MPa
- Compressive strength, 2 days
- B6: ≥45 MPa | B10: ≥35 MPa
- Compressive strength, 28 days
- B6: ≥70 MPa | B10: ≥70 MPa
- Reference test basis
- Typical dry binder laboratory data
- Site effects
- Actual results vary with mix and conditions
FAQ
KREVO Inject MicroCem: questions
What is KREVO Inject MicroCem?
KREVO Inject MicroCem is an ultra-fine blast furnace slag cement system for penetrating fine cracks and voids in concrete, rock and soil. It is intended for specialist injection grouting, ground improvement and upgrading conventional cement grouts and mortars. Two fineness grades, B6 and B10, allow selection to suit the project.
What is KREVO Inject MicroCem used for?
KREVO Inject MicroCem is used for: concrete crack injection; soil and rock stabilization; foundation support; sealing of sheet piles; groundwater cut-off and underground stream sealing; performance enhancement of cement-based grouts and mortars.
What pack sizes is KREVO Inject MicroCem available in?
KREVO Inject MicroCem is supplied in 25 kg bags.
What is the shelf life of KREVO Inject MicroCem?
Shelf life / storage: Dry, shaded conditions, below +25°C.
Is there a technical data sheet for KREVO Inject MicroCem?
Yes. The technical data sheet (PDF) can be downloaded from this page. For project-specific advice or a quotation, send an enquiry to the Krevo technical team.
More in Injection System
Water Plug
Injection System
KREVO Plug Rapid
Ultra-rapid-setting water-stopping mortar · Single-component · Active leak plugging
View product
PU Injection Permanent
Injection System
KREVO Inject PU-Flex
Two-component flexible polyurethane injection resin · Elastic sealing of concrete cracks and leaking joints
View product
PU Injection Temporary
Injection System
KREVO Inject PU-Foam
Water-reactive two-component polyurethane injection foam · Rapid stopping of active leaks
View product