KREVO Anchor EP
High-performance pure epoxy anchoring resin · Cartridge-applied · High-load fixings
- Type
- Anchoring Epoxy
- Pack sizes
- 400 mL cartridge
- Shelf life
- +5 °C to +30 °C; dry, shaded and frost-free
Overview
KREVO Anchor EP is a two-component, pure epoxy resin anchoring grout formulated for fixing starter bars, threaded studs, anchor bolts and sockets in rock, concrete, brick and solid masonry. The cartridge system is suited to horizontal and vertical installations where high bond strength and controlled setting are required.
Advantages
- High-load anchoring resin with good dimensional stability and resistance to vibration.
- Styrene-free formulation and low-VOC performance specification.
- Suitable for horizontal and vertical fixing, including locations near free edges subject to design.
- Designed for use with anchor bolts, starter bars, threaded rods and anchor sockets.
- Can be considered for potable-water contact subject to relevant product approval.
Typical uses
- Starter bars and structural rebar dowels
- Threaded rod and anchor bolt fixings
- Steel anchor sockets
- Connections in concrete, masonry, brick or rock
- Structural rehabilitation and strengthening works
Technical data
Technical properties
Typical values from the technical data sheet. Always confirm with the current data sheet before use.
Key performance
KREVO Anchor EP
< 50 g/L
VOC specification
65.5 MPa
7-day compressive yield | ASTM D695
1,310 MPa
7-day compressive modulus | ASTM D695
46 MPa
7-day tensile strength | ASTM D638
1.9%
7-day elongation | ASTM D638
57 °C
Heat deflection temperature | ASTM D648
0.40%
24-hour water absorption | ASTM D570
0.003
Linear coefficient of shrinkage | ASTM D2566
Product information
- Chemical base
- Two-component, pure epoxy cartridge anchoring grout
- Application
- Horizontal and vertical installation in sound mineral substrates
- Typical substrates
- Concrete, brick, solid masonry and rock
- Typical fixings
- Threaded studs, starter bars, anchor bolts and sockets
- Storage temperature
- +5 °C to +30 °C; dry, shaded and frost-free
- Shelf life
- 24 months under the stated storage conditions
- Permanent service temperature
- −40 °C to +72 °C
- Temporary service temperature
- −40 °C to +120 °C
FAQ
KREVO Anchor EP: questions
What is KREVO Anchor EP?
KREVO Anchor EP is a two-component, pure epoxy resin anchoring grout formulated for fixing starter bars, threaded studs, anchor bolts and sockets in rock, concrete, brick and solid masonry. The cartridge system is suited to horizontal and vertical installations where high bond strength and controlled setting are required.
What is KREVO Anchor EP used for?
KREVO Anchor EP is used for: starter bars and structural rebar dowels; threaded rod and anchor bolt fixings; steel anchor sockets; connections in concrete, masonry, brick or rock; structural rehabilitation and strengthening works.
What pack sizes is KREVO Anchor EP available in?
KREVO Anchor EP is supplied in 400 mL cartridge.
What is the shelf life of KREVO Anchor EP?
Shelf life / storage: +5 °C to +30 °C; dry, shaded and frost-free.
Is there a technical data sheet for KREVO Anchor EP?
Yes. The technical data sheet (PDF) can be downloaded from this page. For project-specific advice or a quotation, send an enquiry to the Krevo technical team.
More in Concrete Repair
Repair Mortar
Concrete Repair
KREVO Repair Mortar
High-strength fibre-reinforced repair mortar · Shrinkage-compensated · Structural concrete restoration
View product
Non Shrink Grout
Concrete Repair
KREVO Grout NS
Shrinkage-compensated cementitious precision grout · Free-flowing, high-strength · 10-50 mm
View product
Micro Concrete
Concrete Repair
KREVO Repair MicroConcrete
Free-flowing high-strength cementitious micro-concrete · Non-shrink repair and grouting · 50-500 mm
View product